11 Things You Need to Consider Before Using Structural Adhesives on Your Repairs.

August 19, 2021 3M Canada

11 Things You Need to Consider Before Using Structural Adhesives on Your Repairs


With the use of structural adhesives in vehicle manufacturing increasing, many OEMs now call for using adhesives when replacing structural parts on a vehicle.

There are a variety of adhesive bonding methods used when replacing automotive body components, including squeeze resistance spot welding or MIG/MAG welding, and sometimes a combo of self-piercing rivets and blind or solid rivets.

There are many specific techniques that are either overlooked by repairers or are described in ambiguous terms in repair guides. In this article, 3M Automotive Aftermarket Division technical experts offer best practices and practical information to help ensure the best repairs possible.

The Importance of OEM Repair Procedures

OEM repair procedures are your most-important resources when using adhesives for automotive repair. Repairers should get year- and model-specific procedures from a reliable source, such as the automotive manufacturers’ web sites and reputable 3rd-party providers of consolidated OEM procedures.

Be aware repair procedures vary by OEM and sometimes between models built by a single company. Some vehicle manufacturers use general statements that recommend a list of applicable adhesives. This type of information, though general, follows a “repair it as it was built” philosophy. Additional content may include specific instructions on combining welding with adhesives to mimic assembly line construction. Weld bonding is the most common of these. Welds may follow a “replace with same number” approach.

Other manufacturers are specific about the adhesive used, generally OEM branded. They may specify the exact locations where adhesive should be applied, specified cleaners, adhesion primers, the number and location of the welds—even the grades of abrasives used for preparation. Some manufacturers advise rivet bonding procedures to replace welding that was performed on the assembly line.

It is rare for OEMs to advise the use of adhesives alone. In those rare cases one or two joints on a panel may be bonded with adhesives only, but the remaining joints are spot-welded or weld-bonded. Always consult specific model and year information to determine the correct procedure.

11 Best Practices When Following OEM Guidelines

If repairers are following OEM guidelines, they should ask themselves what other considerations they might have. Whether the OEM guide was developed with very specific details or not, repair professionals should always follow some general best practices around the use of adhesives and panel preparation.

  1. Use fresh abrasives and the correct grade(s) determined by either the OEM or the adhesive supplier.
    Avoiding cross-contamination of metallic substrates is especially important when working with dissimilar metals. Often you may be joining steel to aluminum—don’t grind/sand both the panels with the same disc or belt.

  2. Choose the adhesive advised by the OEM.
    You may see the use of the phrase “or equivalent” language in the repair manual. Unless you have some written proof of equivalency that has been published by a manufacturer, be careful deviating from the prescribed adhesive.

  3. Unless advised otherwise by the OEM, follow the adhesive manufacturer’s directions for use.
    They have determined the procedures, methods of preparation and application at which the adhesive performs optimally and meets their specific required standards.

  4. Always use adhesives that are within shelf-life.
    Most companies use expiration dates that are easily identifiable to the public. If not, consult the adhesive manufacturer for identification of the code.

  5. Never cross over equipment such as static mix nozzles from one manufacturer to another.
    Not all tools are created equally, and the varying designs can cause improper mixing.

  6. Never assume that the current-year model repair procedures are the same as previous years.
    Always consult the OEM repair procedures even when models appear to be identical.

  7. Never assume that one adhesive may be used on all panels of the same model.
    Some OEMs have different adhesive advisements related to specific panels on the same vehicle.

  8. Get the training and knowledge required for the job.
    Body repair is more complicated and requires more knowledge now than it ever has. Be sure to get proper training and familiarize yourself with necessary procedures.

  9. Be aware of the temperature of your shop, both during the day and at night.
    The temperature for determining the work time, clamp time and cure time displayed on an adhesive’s package is typically 21.1°C to 23.9°C (70°F to 75°F). If you turn off the heat in your shop at night and the temperature drops to 4.4°C (40°F) for eight hours after you bonded a panel, you will have to raise the temperature back to 21.1°C to 23.9°C (70°F to 75°F) and then wait the specified clamp time.

  10. Make note of corrosion on host panels.
    If host panels have corrosion that cannot be removed, it is best to consult the customer and consider replacing the host panel as well. If nothing else, be sure to document the corrosion damage with photos. Adhesives may have the ability to help prevent corrosion on uncorroded panels, but if heavy corrosion is already present, bond strength will be lost, and corrosion growth will—at best—only be slowed.

  11. Consider using OEM-recommended corrosion protection.
    Most OEMs advise the use of corrosion protection internally and externally even when bonding procedures have been used. This ensures the bond is protected and if any bare metal was exposed during the placement of the new part, it has been protected.

Remember, you are the frontline decision maker when it comes to doing the repair. Your customer is trusting you to do things the right way. Following the OEM repair procedures combined with ongoing training is the foundation for performing safe repairs that benefit both your customers and your business.

For more information about using structural adhesives on your repair, please reach out to your local 3M Collision Repair Specialist or visit us online at 3M.ca/BodyRepair.

Written by: Dennis Keicher, Advanced Application Development Specialist 3M Automotive Aftermarket Division

About the Author

3M Canada

[enBio=Across the globe, 3M helps companies and individuals succeed every day. All while contributing to true global sustainable development through environmental protection, corporate and social responsibility and economic progress. We are applying our science to make a real impact in every person's life around the world.],[enJob=Science. Applied to Life.],[frBio=Chaque jour, 3M aide les entreprises et les gens à réussir. Tout cela en contribuant au développement durable réel par le biais de la protection de l'environnement, la responsabilité sociale en entreprise et le progrès économique. Nous appliquons notre science afin de faire une différence réel dans la vie de chaque personne dans le monde.],[frJob=Science. Au service de la Vie.]

Follow on Twitter Follow on Linkedin Visit Website More From 3M Canada
Previous Article
3M Tech Talk: Paint booth protection.
3M Tech Talk: Paint booth protection.

Next Article
5 Tips to Avoid Over-Grinding with Your File Belt
5 Tips to Avoid Over-Grinding with Your File Belt